Development of Lead-Free Radiation Shielding Material Utilizing Barium Sulfate and Magnesium Oxide as Fillers in Addition Cure Liquid Silicone Rubber.

The radiological protection has the purpose of safeguarding the physical well-being of the user, preventing exposure to detrimental levels of ionizing radiation. This study introduces a novel, cost-effective category of lead-free elastomeric material designed for radiation shielding. The filler compounds utilized are notably lighter than conventional lead-based materials, enhancing user ergonomics during application. They comprise of a blend of barium sulfate combined or not with magnesium oxide with addition-cure liquid silicone rubber. To ensure the effectiveness of the radiation shielding, X-ray transmission measurements were performed for the different thicknesses of the materials and the results compared with Monte Carlo simulations. Additionally, the physical properties of the new materials, such as density, homogeneity, tensile strength, viscosity, and wettability, were also evaluated. The findings indicate that both materials fulfill the requirement for application in radiation protection garments.

Evaluation of a biobased polycarbonate interpenetrated network in a dental resin composite.

Silanization of filler particles in a dental resin composite is achieved by the formation of Si-O-Si bonds, however, these bonds are especially vulnerable to hydrolysis because this covalent bond has a significant ionic character due to the electronegativity differences between the atoms. The objective of this study was to evaluate the use of an interpenetrated network (IPN) as alternative of silanization reaction and to assess its effect in selected properties of experimental photopolymerizable resin composites. The interpenetrate network was obtained during the photopolymerization reaction of organic matrix (BisGMA/TEGDMA) with a biobased polycarbonate. Its characterization was performed via FTIR, flexural strength, flexural modulus, depth of cure, sorption water and solubility. A resin composite formulated with non-silanized filler particles was used as control. The IPN with a biobased polycarbonate was successfully synthesized. The results showed that the IPN based resin composite had higher values of flexural strength, flexural modulus, and degree of double bond conversion than the control (p < 0.05). Polymerization shrinkage, water sorption and solubility were statistically significantly lower than the control resin (p < 0.05). Finally, this study shows there were no statistically significant differences for the biocompatibility outcomes (p > 0.05). The biobased IPN replaces the silanization reaction in resin composites, improving physical and chemical properties. Therefore, IPN with a biobased polycarbonate could be potentially useful in the formulation of dental resin composites.

Synthesis and characterization of calcium-releasing elastomeric resin-based endodontic sealers.

OBJECTIVES: To evaluate the incorporation of halloysite nanotubes (HNTs) loaded with one of two calcium sources (i.e., calcium hydroxide/CaOH2 or beta-tricalcium phosphate/ß-TCP) on the physicochemical and biological properties of an experimental resin-based dual-cured endodontic sealer. MATERIALS AND METHODS: HNTs were encapsulated with CaOH2 or ß-TCP at 10 wt.%. HNTs containing CaOH2 or ß-TCP were added into the experimental sealers at 50 wt.%. The control sealers were the calcium-free HNT-modified resin-based experimental sealer and AH Plus™, a commercially available endodontic sealer. Degree of conversion, setting time, flow, film thickness, radiopacity, dimensional stability, and calcium ions release were determined. Antibiofilm properties and cytocompatibility of the formulated sealers and commercial control were also evaluated. One and two-way ANOVA analysis followed by Tukey's post hoc test was conducted to evaluate the effect of the independent variable on the evaluated properties. RESULTS: FTIR confirmed the encapsulation of calcium sources into HNTs. Regarding flow and film thickness, the values obtained from these sealers were in accordance with the specifications provided by ISO 6876. For radiopacity, AH Plus™ achieved the highest radiopacity (p<0.05). Among the experimental formulations, all experimental HNT-containing compositions exhibited values below 3 mm Al. The experimental sealers showed greater dimensional changes when compared to the commercial (AH Plus™) control. The release of calcium ions was observed for the HNT_CaOH2 and HNT_ß-TCP sealers without statistical differences. Experimental sealers containing HNT_CaOH2 and HNT_ß-TCP significantly reduced the CFU/mL count and showed cell compatibility. CONCLUSIONS: The findings of this study demonstrate that the incorporation of HNT_CaOH2 or HNT_ß-TCP into resin-based experimental sealers promoted antimicrobial effects and gradual calcium release without impairing cytocompatibility or physicochemical properties of the sealers. Still, an adjustment to reach the minimal radiopacity established by ISO 6876 is needed. CLINICAL RELEVANCE: The experimental resin-based sealers seemed to be an alternative for endodontics. The incorporation of calcium sources exerts promising antimicrobial effects while displaying low cell toxicity.

Physical properties, marginal adaptation and bioactivity of an experimental mineral trioxide aggregate-like cement modified with bioactive materials.

PURPOSE: To evaluate the effect of adding wollastonite and bioactive glass to an experimental mineral trioxide aggregate-like cement (MTA) on the dimensional stability, compressive strength, solubility, bioactivity, and marginal adaptation by scanning electron microscopy (SEM) and X-ray diffraction (XRD). METHODS: Four groups were evaluated at 7, 14, and 21 days: MTA Angelus, experimental MTA-like cement (MTA Exp), BG10 (MTA Exp+10 wt% bioactive glass), and WO20 (MTA Exp+20 wt% wollastonite). To evaluate marginal adaptation, extracted teeth were endodontically obturated and root-end cavities were prepared and filled with the tested materials. RESULTS: Cements with bioactive materials showed minimal dimensional changes. Adding wollastonite or bioactive glass to MTA Exp reduces the compressive strength but does not affect solubility. Bismite (Bi2O3), larnite (Ca2SiO4), calcite (CaCO3) and carbonated hydroxyapatite (Ca5[PO4,CO3]3[OH]) were identified in the four cements; ettringite (Ca6Al2[SO4]3[OH]12·26H2O) and bismutite ([BiO]2CO3) were only observed in MTA Exp, BG10, and WO20. Cement-dentin interfaces were not observed after 14 days on the BG10 and WO20 cement composites due to the ettringite formation. CONCLUSION: Acicular growing crystals typical of hydroxyapatite were found on the surfaces of all cements. An improved marginal adaptation was observed with the addition of wollastonite or bioactive glass.

A multi-country survey on the impact of COVID-19 on dental practice and dentists' feelings in Latin America.

BACKGROUND: The COVID-19 pandemic has significantly influenced the routine of healthcare workers. This study investigated the impact of the pandemic on dental practice and dentists' feelings in Latin America. METHODS: A survey was conducted with dentists from 11 Spanish-speaking Latin American countries in September-December 2020. Professionals were invited by email and via an open campaign promoted on social media. The questions investigated dental care routines, practice changes, and feelings about the pandemic. Descriptive statistics were used to identify frequencies and distributions of variables. Proportions were compared using chi-square tests. RESULTS: A total of 2127 responses were collected from a sample with diverse demographic, sex, work, and education characteristics. The impact of COVID-19 was considered high/very high by 60% of respondents. The volume of patients assisted weekly was lower compared with the pre-pandemic period (mean reduction = 14 ± 15 patients). A high rate of fear to contracting the COVID-19 at work was observed (85%); 4.9% of participants had a positive COVID-19 test. The main professional challenges faced by respondents were reduction in the number of patients or financial gain (35%), fear of contracting COVID-19 (34%), and burden with or difficulty in purchasing new personal protective equipment (22%). The fear to contracting COVID-19 was influenced by the number of weekly appointments. A positive test by the dentists was associated with their reports of having assisted COVID-19 patients. The most cited feelings about the pandemic were uncertainty, fear, worry, anxiety, and stress. Negative feelings were more prevalent for professionals who did not receive training for COVID-19 preventive measures and those reporting higher levels of fear to contract the disease. CONCLUSION: This multi-country survey indicated a high impact of the pandemic on dental care routines in Latin America. A massive prevalence of bad feelings was associated with the pandemic.

In vitro Streptococcus mutans adhesion and biofilm formation on different esthetic orthodontic archwires.

OBJECTIVES: To evaluate the ability of different esthetic archwires to retain oral biofilms in vitro. MATERIALS AND METHODS: Seven different brands of coated orthodontic archwires were tested: two epoxy coated, two polytetrafluoroethylene coated, two rhodium coated, and one silver plus polymer coated. Conventional uncoated metallic archwires were used as controls. Streptococus mutans adherence to archwires was quantified by colony count following 24 hours of biolfilm growth, and total wire-associated biofilm was measured using a crystal violet staining assay. For both tests, two conditions were used: 0% sucrose and 3% sucrose. For statistical analysis, P < .05 was considered as statistically significant. RESULTS: For S. mutans colony forming units per biofilm, there were no statistically significant differences among the various archwires (P = .795 for 0% sucrose; P = .905 for 3% sucrose). Regarding total biofilm formed on archwires in the 3% sucrose condition, there were statistically significant differences in crystal violet staining only for the comparison between Niti Micro Dental White and Copper Ni-Ti wires (P < .05). CONCLUSIONS: The clinical use of esthetic-coated orthodontic wires may be considered to have similar risks as uncoated archwires for biofilm retention.

Physicomechanical, optical, and antifungal properties of polymethyl methacrylate modified with metal methacrylate monomers.

STATEMENT OF PROBLEM: The high recurrence rates of denture stomatitis may be associated with the resistance of biofilms to therapeutics. Therefore, methods that provide biomaterials with antifungal properties are an attractive solution to improving microbial control. PURPOSE: The purpose of this in vitro study was to modify conventional polymethyl methacrylate (PMMA) through the incorporation of metal methacrylate monomers and to evaluate the physicomechanical and optical properties and antifungal activity of the modified materials. MATERIAL AND METHODS: Experimental denture base acrylic resins were fabricated through the addition of zirconium methacrylate (ZM), tin methacrylate (TM), and di-n-butyldimethacrylate-tin (DNBMT) to the liquid of a commercially available denture base PMMA resin. Unmodified PMMA resin was used as the control. The degree of conversion of the materials was tested through Fourier transform infrared spectroscopy (n=3). A digital spectrophotometer was used to assess the color change of the modified materials (n=8). Differences in Knoop hardness and roughness between experimental groups were also evaluated (n=8). A biofilm accumulation test with Candida albicans (ATCC 62342) (n=4) was performed for 5 days in Sabouraud broth culture supplemented with 10% sucrose. Data were subjected to analysis of variance and the post hoc Tukey honestly significant difference test (α=.05). RESULTS: The degree of conversion and color-change values of the experimental materials were statistically similar to those of the control (P=.593). The incorporation of DNBMT significantly increased the hardness of the modified material (P=.014). The ZM, TM, and DNBMT groups had higher antifungal activity against C. albicans (P=.001) and lower roughness than the control group (control 0.65 ±0.05 µm; ZM 0.34 ±0.09 µm, TM 0.34 ±0.11 µm, and DNBMT 0.41 ±0.08 µm). CONCLUSIONS: The metal-containing methacrylate monomers provided antifungal action to the modified materials without affecting the physicomechanical or optical properties of the denture base resin. ZM, TM, and DNBMT are potential reactive agents for the fabrication of PMMA denture base resins with antifungal properties.

Development of an antibacterial and anti-metalloproteinase dental adhesive for long-lasting resin composite restorations.

Despite all the advances in adhesive dentistry, dental bonds are still fragile due to degradation events that start during application of adhesive agents and the inherent hydrolysis of resin-dentin bonds. Here, we combined two outstanding processing methods (electrospinning and cryomilling) to obtain bioactive (antimicrobial and anti-metalloproteinase) fiber-based fillers containing a potent matrix metalloproteinase (MMP) inhibitor (doxycycline, DOX). Poly(ε)caprolactone solutions containing different DOX amounts (0, 5, 25, and 50 wt%) were processed via electrospinning, resulting in non-toxic submicron fibers with antimicrobial activity against Streptococcus mutans and Lactobacillus. The fibers were embedded in a resin blend, light-cured, and cryomilled for the preparation of fiber-containing fillers, which were investigated with antibacterial and in situ gelatin zymography analyzes. The fillers containing 0, 25, and 50 wt% DOX-releasing fibers were added to aliquots of a two-step, etch-and-rinse dental adhesive system. Mechanical strength, hardness, degree of conversion (DC), water sorption and solubility, bond strength to dentin, and nanoleakage analyses were performed to characterize the physico-mechanical, biological, and bonding properties of the modified adhesives. Statistical analyses (ANOVA; Kruskal-Wallis) were used when appropriate to analyze the data (α = 0.05). DOX-releasing fibers were successfully obtained, showing proper morphological architecture, cytocompatibility, drug release ability, slow degradation profile, and antibacterial activity. Reduced metalloproteinases (MMP-2 and MMP-9) activity was observed only for the DOX-containing fillers, which have also demonstrated antibacterial properties against tested bacteria. Adhesive resins modified with DOX-containing fillers demonstrated greater DC and similar mechanical properties as compared to the fiber-free adhesive (unfilled control). Concerning bonding performance to dentin, the experimental adhesives showed similar immediate bond strengths to the control. After 12 months of water storage, the fiber-modified adhesives (except the group consisting of 50 wt% DOX-loaded fillers) demonstrated stable bonds to dentin. Nanoleakage was similar among all groups investigated. DOX-releasing fibers showed promising application in developing novel dentin adhesives with potential therapeutic properties and MMP inhibition ability; antibacterial activity against relevant oral pathogens, without jeopardizing the physico-mechanical characteristics; and bonding performance of the adhesive.

Dental composite resins with low polymerization stress based on a new allyl carbonate monomer.

The objective of this study was to synthesize a diallyl carbonate monomer, allyl(2-(2-(((allyloxy)carbonyl)oxy)benzoyl)-5-methoxyphenyl) carbonate (BZ-AL), and to evaluate its effect as Bis-GMA diluent in the formulation of photopolymerizable dental composite resins. The chemical structure of BZ-AL monomer was determined by means of H1 NMR, C13 NMR and FTIR spectroscopies. An experimental composite comprising a mixture of Bis-GMA and BZ-AL monomers and silanized inorganic filler was formulated. Experimental material was compared with a control composite formulated with Bis-GMA/TEGDMA. Double bond conversion, polymerization kinetics, volumetric shrinkage, polymerization stress, and flexural properties were investigated. The data were analyzed through a Student t-test (α = 0.05). Flexural strength of the experimental materials with BZ-AL monomer showed a statistically significant increase (p < 0.001). The experimental composite has a lower polymerization rate than the control composite, on the other hand, the experimental composite resin has the highest degree of double bond conversion. There are no differences in the polymerization shrinkage of the composites, however, the polymerization stress of the experimental materials was 50% lower than the control resin. Finally, the cell viability test showed that the experimental resins formulated with the BZ-AL monomer was not cytotoxic. Due to its characteristics, BZ-AL monomer is potentially useful for the formulation of composite materials with applications in dentistry.

Cytotoxicity of contemporary resin-based dental materials in contact with dentin.

In this study, the cytotoxicity of different combinations of contemporary resin-based restoratives (adhesives, composites, luting agents) against human keratinocytes (HaCaT) was evaluated under two conditions, whether materials were applied to dentin or not. Adhesives (3-step etch-and-rinse/3ER: OptiBond FL; 2-step self-etch/2SE Clearfil SE Bond; Single Bond Universal/UNI), composites (conventional composite resin/CCR: Filtek Z350XT; flowable/FCR: Filtek Z350XT Flow; self-adhesive composite resin/SACR: Dyad Flow), and luting agents (conventional luting agent/CLA: Variolink-II; self-adhesive luting agent/SLA: RelyXU200) were combined according to their clinical use. Eluates from polymerized specimens applied to dentin were placed in contact with cells grown for 1 and 7 d. The controls were defined by cells without material contact. Cell viability was determined using MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide)] assay. C=C conversion was investigated using Fourier-transform infrared spectroscopy. After 1 d of incubation, when dentin was not present, 2SE yielded the highest cell viability, whereas 3ER, UNI, and SACR showed higher cell viability in the presence of dentin. After 7 d, when dentin was absent, 2SE and CLA achieved significantly higher cell viability. The presence of dentin resulted in a drastically higher cell viability for all materials, except 2SE and CLA. UNI had the lowest C=C conversion. The presence of dentin was a significant factor, which resulted in higher cell viability than what was seen for the material specimens per se. All materials resulted in a lower viability of HaCaT than what was seen under the no-material control conditions, with effects mainly limited to the first 24 h.

Preparation and evaluation of a BisGMA-free dental composite resin based on a novel trimethacrylate monomer.

OBJECTIVE: The use of the BisGMA as base monomer in dental composites has been questioned because of bisphenol A (BPA) is used as raw material in its synthesis, and BPA possess estrogenic potential associated to several health problems. This study describes the synthesis of the trimethacrylate tris(4-hydroxyphenyl)methane triglycidyl methacrylate (TTM) monomer and evaluate its effect when used as base monomer in the formulation of experimental photopolymerizable composite resins. METHODS: The TTM monomer was synthesized by a nucleophilic acyl substitution. Its chemical structure was confirmed via 1H and 13C NMR spectroscopy and FTIR spectroscopy. Experimental composite resins were formulated by mixing TTM, triethyleneglycol dimethacrylate (TEGDMA) and inorganic fillers. A BisGMA/TEGDMA based composite resin was prepared and used as control to compare several physicochemical properties. Cell viability assay was used for cytotoxicity evaluation. RESULTS: TTM was successfully synthesized with quantitative yields. The results showed that the TTM-based composite resin had similar values of flexural strength, elastic modulus, degree of conversion and polymerization shrinkage than the control (p > 0.05). Water sorption and solubility were statistically significantly higher than the control (p < 0.05), however they complied the requirements stablished by the ISO 4049. Finally, this study shows there were no statistically significant differences for the biocompatibility outcomes (p = 0.345). SIGNIFICANCE: TTM monomer could be potentially useful in the formulation of BisGMA free composite resins, which could mean to minimize the human exposure to BPA.

Evaluation of dental composites resins formulated with non-toxic monomers derived from catechol.

Two liquid monomers (CT-AL and CT-ACR) were synthesized from the acylation of tert-butyl catechol with different acid chlorides. The monomers were used to prepare photopolymerizable dental composite for completely replacing TEGDMA. Properties such as flexural strength, modulus of elasticity, degree of double bond conversion, polymerization shrinkage, as well as the polymerization stress were studied. Also, color alteration, translucency, and cytotoxicity were evaluated. The results show that the experimental materials formulated with CT-AL and CT-ACR have similar mechanical properties to a control material formulated with BisGMA/TEGDMA, similar polymerization shrinkage, and less polymerization stress. The composite formulated with the CT-AL monomer shows a similar degree of conversion (72%), while the composite formulated with the CT-ACR monomer has a degree of conversion lower (58%) than the control resin (71%). These results suggest that both monomers could have potential applications in the formulation of composites for dental restorations.

Evaluation of alternative photoinitiator systems in two-step self-etch adhesive systems.

OBJECTIVE: The aim of this study was to evaluate the effect of different photoinitiator systems on the cell viability and physico-chemical properties of an experimental adhesive resin of a two-step self-etch adhesive system. METHODS: Eight photoinitiators and coinitiators were evaluated, camphorquinone (CQ); ethyl-dimethylamino benzoate (EDAB); diphenyliodonium hexafluorophosphate (DPIHFP); 1,3-benzodioxole (BDO); piperonyl alcohol (AP); 1,3-diethyl-2-thiobarbituric acid (TBA); bisphenyl phosphinic oxide (BAPO); and diphenyl phosphinic oxide (TPO). Seven experimental adhesive resins (Bis-GMA:TEGDMA - 1:1 by wt%) were formulated by varying the initiation systems: RCQ+EDAB (control), RCQ+EDAB+DPHFP, RCQ+BDO, RCQ+AP, RCQ+TBA, RBAPO and RTPO. The cell viability of the different photoinitiators in their isolated form and after being incorporated into the adhesive resins was evaluated using the MTT assay. The degree of conversion within the hybrid layer (DC in situ) was evaluated by micro-Raman spectroscopy; the polymerization kinetics, by FTIR spectroscopy. The water sorption (Wsp) and solubility (Wsl) were calculated by using percentage of gain and loss of mass. Data were analyzed using One-way ANOVA and Kruskal-Wallis tests (α=0.05). RESULTS: When evaluated in their isolated form, the DPIHFP was considered cytotoxic in all concentrations evaluated. When incorporated into and adhesive resin, RCQ+TBA presented higher cell viability values than control and the highest values of DC in situ (p<0.05). Additionally, the use of CQ+TBA showed a higher cell viability when compared with the conventional CQ+EDAB system. SIGNIFICANCE: The pair CQ+TBA could be potentially useful in the development of materials with improved biocompatibility.

Evaluation of biocompatible monomers as substitutes for TEGDMA in resin-based dental composites.

This works reports the synthesis and characterization of diallyl(5-(hydroxymethyl)-1,3-phenylene) dicarbonate (HMFBA) and 5-(hydroxymethyl)-1,3-phenylene bis(2-methylacrylate) (HMFBM) monomers and its evaluation as Bis-GMA eluents in the formulation of composite resins for dental use. The experimental materials formulated with HMFBA and HMFBM monomers presented flexural strength values similar to those of the control group formulated with Bis-GMA/TEGDMA. Regarding volumetric contraction percentage, the values obtained of experimental materials with HMFBA was 1.88% and for HMFBM was 4.15%, both lower than control resin (4.68%). In the case of double bond conversion, the resin formulated with HMFBA monomer exhibited a greater degree of conversion (87%). Besides, the DMA analyses proved that the values for Tg guarantee a good mechanical performance at body temperature. The new resins formulated with HMFBA and HMFBM monomers exhibit a cellular viability close to 100%, which indicates the absence of cytotoxicity towards fibroblastic cells.

Synthesis of an allyl carbonate monomer as alternative to TEGDMA in the formulation of dental composite resins.

Over the past years, significant effort has been dedicated to synthesizing low-shrinking formulations, however, development of dental composites with low volumetric shrinkage continues to be challenging. The purpose of this study was to synthesize a bisphenol allylic derivate (BPhADAC) and evaluate its inclusion in the formulation of a photopolymerizable dental composite resin, as a BisGMA diluent. Experimental (BisGMA/BPhADAC) and control (BisGMA/TEGDMA) photopolymerizable composites were prepared. Double bond conversion, polymerization kinetics, volumetric shrinkage, water sorption, solubility, and flexural properties were investigated. The experimental composite showed higher degree of conversion values, less volumetric shrinkage and less water sorption than the control composite (p < 0.05). In addition, flexural strength between the materials was found to be similar. The overall properties prove that the allylic monomer BPhADAC could be potentially useful in the formulation of low-shrinking dental composite resins.

Histological Evaluation of Bone Repair with Hydroxyapatite: A Systematic Review.

The aim of this study was to evaluate the morphological bone response in animal experiments by applying hydroxyapatite grafts in critical and non-critical size bone defects. Current report followed the guidelines established by the Preferred Reporting Items for Systematic Reviews and Meta-Analyses. Animal experiments were selected by assessing repair of bone defects with hydroxyapatite as bone graft and with blood clot only as control. Eight articles were identified in specialized literature and included in the meta-analysis. Statistical analysis was carried out with a random-effect model (p = 0.05). Subgroup analyses were further performed to investigate bone repair in critical and non-critical bone defects. Comprehensive analysis of bone repair outcome showed a statistically significant difference between hydroxyapatite and blood clot control (p < 0.05). Subgroup analyses showed statistically significant difference for critical bone defects (p < 0.05). No statistically significant difference was reported in non-critical bone defects (p > 0.05). Although animal studies revealed a high risk of bias and results should be interpreted with caution, the literature suggests that non-critical bone defects may heal spontaneously and without the need of a bone graft. Conversely, when critical-size defects are present, the use of hydroxyapatite bone graft improves the bone repair process.

Prevalencia de dentición funcional en ancianos mexicanos / Prevalence of functional teeth in Mexican elderly

Objetivo: Determinar la prevalencia de dentición funcional (DF) y su distribución a través de diversas variables clínicas, sociodemográficas y socioeconómicas de una muestra de ancianos mexicanos. Material y métodos En un estudio transversal se incluyeron 139 adultos de 60 años y más de 2 asilos y un club de ancianos de la ciudad de Pachuca, Hidalgo, México. La variable dependiente fue la dentición funcional; operacionalmente categorizada como: 0 = sujetos con menos de 21 dientes presentes en la boca y 1 = sujetos con 21 o más dientes en la boca, excluyendo prótesis. Las variables sociodemográficas, socioeconómicas y conductuales se recogieron a través de un cuestionario. Las variables clínicas fueron recabadas por un examinador capacitado y estandarizado. El análisis se realizó utilizando pruebas no paramétricas en Stata. Resultados El promedio de edad fue de 79,06 +/- 9,78. La mayoría de los sujetos incluidos fueron mujeres (69,1 por ciento). La prevalencia de dentición funcional fue de 10,1 por ciento. En el análisis bivariado observamos lo siguiente: los sujetos con DF tuvieron menor edad (p < 0,05); entre las mujeres se observó mayor prevalencia de DF (p < 0,05); las personas con pareja presentaron más alto porcentaje de DF (p < 0,05); la prevalencia de DF fue diferente a través de los tipos de asilamiento (p < 0,05). Conclusiones Los datos sugieren una baja prevalencia de dentición funcional en esta muestra de adultos mayores. Este estudio demuestra que la DF varía en función de variables sociodemográficas.

Objective: To determine the prevalence of functional teeth (FT) and their distribution using clinical, demographic, and socioeconomic variables in a sample of Mexican elderly. Material and methods This cross-sectional study of 139 adults aged 60 years and older was conducted in two nursing homes and one club in Pachuca, Hidalgo, Mexico. The dependent variable was FT, and participants were operationally categorised as 0 (having less than 21 teeth) or 1 (having 21 or more teeth). Those categorised as 1 comprised the FT group. Sociodemographic, socioeconomic, and behavioural variables were collected using a questionnaire. Clinical variables were collected by a trained examiner using a standardised examination. Analysis was performed using non-parametric tests in Stata. Results The mean age was 79.06 +/- 9.78 years. Most (69.1 percent) of the participants were women. The prevalence of FT was 10.1 percent. In the bivariate analysis, it was observed that the FT group was younger (p < .05), women displayed a greater prevalence of FT than men (p < .05), as did those involved in a relationship compared to being single (p < .05), and FT prevalence differed by type of isolation (p < .05). Conclusions The prevalence of FT is low among nursing home residents and club members, and it varies with age, sex, relationship status, and type of isolation.